Data loggers
In conclusion, from the data loggers
The data demonstrates comparatively low dew points. However, the low temperature of the front wall, in part caused by the heat loss from the sub-floor vent and curtain is causing high surface relative humidity, resulting in mould. See my additional evidence and recommendations.
Evidence and illustrations
To keep the property dry | |
|---|---|
| Target vapour from bathroom | |
| TIP: Keep the bathroom door closed with the fan running or window open until the humidity from the shower has subsided – typically at least 30 mins after the last shower. | |
| Target vapour from cooking with an extractor fan | |
| Cook with tops on pots and pans and use the extractor fan | |
| Target vapour from clothes drying | |
| Use a tumble dryer (like a heat pump), dry in a vented room with the door closed (possibly a bathroom with the extractor running or window open), or use a powerful dehumidifier. Don’t dry clothes in an unventilated room. | |
| Remove mould | |
| Consider sanding down mould where dry, and removing it with either bleach or anti-mould foam. I personally use HG Mould Remover Foam Spray, but imagine there is no major difference between brands. | £100 |
| Use a dehumidifier | |
| Maintain relative humidity, especially at night when it’s cold outside, with a dehumidifier such as PureMate 20L/Day Portable & Compact Dehumidifier with 6.5 Litre (£179.99 Refrigerant), Duux Bora Smart Dehumidifier (DXDH02UK £300 Refrigerant) or Meaco DD8L Zambezi (£260 Desiccant – best for colder environments) – Which! Best buys. There are plenty of alternatives available. I choose a dehumidifier based on daily and tank capacity, low noise, whether it has a pipe out, and ease of programmable functions over other considerations such as weight and aesthetics. The technology is old and easy to manufacture. So if these brands are not available, you are sure to find another alternative. Evaluate based on daily capacity (20L minimum) and whether it has a continuous pipe out (use this to drip into a sink when away in winter). | £180 |
| Open curtains | |
| Sometimes the smallest things make the greatest difference. Curtains act as insulation, stopping heat from escaping. Vapour moves through diffusion, like smoke. While the curtains will slow the diffusion of vapour down, more vapour will get through than heat, resulting in higher surface relativity and a prolonged period of consistent and high relative humidity. Of course it is better and typically cheaper and more environmentally friendly to use a dehumidifier to reduce the vapour in air, but if you don’t have one or anyway aren’t running one, then pulling curtains away from the wall, including during the day to reduce surface relative humidity. | |
| Use fan to expedite drying | |
| Direct a fan onto the damp patch to speed up the drying process. | |
| Unblock down-pipe | |
| I tried to free cement and other builder’s material blocking the down-pipe. I suggest using an old metal hanger straightened or buying a plumber snake, pushing the detritus up. See. Above link for further recommendations. | |
| Remedial actions – estimate of costs | £280 |
Actions if all else fails | |
|---|---|
| Consider installing a continuous flow bathroom extractor fan | |
| Consider installing a continuous flow bathroom extractor fan such as Vent Axia or Brookvent Airstream DMEV 100 HT (Continuous Running Extractor Fan with Humidistat Timer). Ideally the vent should be located away from the door, closer to the shower. | £300 |
| Consider targeted insulation | |
| Consider insulating damp and mouldy zones with thermal insulating lining paper, such as wallrock, or in the bathroom, Sempatap (effective, German made, rubber backed lining paper, less good for the front bay as could result in some interstitial condensation). | £200 |
| Consider closing sub-floor airbricks | |
| Sub-floor air vents can be a source of significant heat loss within a property. In the pursuit of energy efficiency and environmental friendliness, an alternative approach involves the temporary sealing of these air bricks, for instance, using products like rubberised flood protection devices (e.g., FloodKit Airbrick Plate, available at FloodKit), and monitoring sub-floor relative humidity, reopening as required. | £200 |
| Optimal actions – estimate of costs | £700 |
I conclude that dampness and mould from excess vapour, compounded by heat loss and curtain placement.
Ineffective use of kitchen and bathroom fans increasing humidity
. By taking a root cause approach, rather than a focus on blocking the symptoms of damp the savings are likely to be around £1,500. This contrasts with typical damp proofing contractor recommendations such as chemical treatment for rising damp and untargeted ventilation, such as PIV systems.
Flood risk: Low risk See Flood Risk (note most flood risk is not from groundwater).
Sub-soil rocks: Near low productive aquifer with intergranular flow See British Geological Survey.
Therefore risk of Rising Damp: low risk, see explanation by Dr Robyn Pender of Historic England.
I confirm that I inspected the property on 231115SH0800. I conclude that dampness and mould from excess vapour, compounded by heat loss and curtain placement. All buildings can be exposed to unvented vapour and external dampness to some degree. You will mitigate the risk of damp if you follow all our recommendations. This report is intended to be read in full including supplementary links in this report. Observations and opinions must not be taken in isolation. Given the right weather conditions almost any house can be affected by rain. Like any building, you need to be aware of the risks of damp arising in the future and should plan a programme of monitoring, prevention and maintenance accordingly. Damp Surveys Ltd reports are designed to provide you with an informed, independent expert opinion as to the cause of dampness in the property, together with any recommendations for further investigation or remedial work. We do not warrant any findings in this report unless we enter into a separate warranty agreement with you.
The survey was conducted during daylight hours. Damp will be more noticeable at night and when the weather is colder and more humid. Gutters are more likely to fail when full of leaves and during periods of prolonged rain and adverse wind. We make best endeavours but cannot guarantee being able to identify all forms of damp, rot and insect infestation affecting the property.
We carried out a careful and thorough inspection of as much of the property as was accessible. However, when a full inspection is not possible, we make a professional judgement regarding the likelihood of a defect being present. In certain circumstances, this may lead to a recommendation for further action to open up an area for additional investigation. We were unable to inspect the entire roof, all the guttering, and some of the drains. Similarly, inspection of woodwork or other parts of the structure that were covered, unexposed, poorly lit or inaccessible such as in the loft, cellar, or sub-floor void was not possible, and therefore we are unable to assert that such parts of the property are free from defect. There were no obvious signs of damp resulting from these limitations
Negligence claims must be made within 90 days of the damp survey site visit. Clients must make best endeavours to monitor humidity and temperature on a damp wall and the closest source of humidity, by purchasing and placing two data loggers for example the Smart Hygrometer measuring humidity on the wall and nearest source of vapour, before and after following our recommendations. These data loggers have sufficient memory capacity to store 90 days of data.
This report is for the sole use of the client (named on the invoice, but omitted here for anonymity) for whom the survey was undertaken and can only be relied upon for 90 days from the survey date. Unless expressly stated otherwise in this report, nothing in this report confers or is intended to confer any rights on any third party pursuant to the Contracts (Rights of Third Parties) Act 1999.
Simon Hichens
Site visit 231115SH0800
Simon Hichens BSc Chemistry RICS Qualified Expert Witness (Chartered Surveyors)
PCA Certificated Surveyor of Dampness & Timber in Buildings (Property Care Association)
Damp Surveys Ltd, 119 Longton Ave London SE26 6RF Reg. 10977488 (England & Wales)
Founder of damp.aï & Member of the Society for the Protection of Ancient Buildings (SPAB)
Our damp surveys are designed to provide a holistic diagnosis that identifies and deals with causes rather than a focus on symptoms. Symptoms will disappear over time, once damp is stopped at source. We look for risks of dampness, but unless moisture is present, we can’t guarantee to identify all risks of future moisture. Our reports:
- identify root cause(s) of major unwanted dampness within the property,
- identify major symptoms of unwanted dampness,
- identify major structural damage caused by dampness,
- recommend actions and estimated costs to stop damp at source and mitigate its effects,
- recognise that treating damp is often a staged approach, treating obvious causes first.
Understanding damp
For survey purposes, damp is defined as unwanted water. Water brings life. We need it. Unfortunately, fungus and insects also thrive in water. While a damp wall can cause decorative spoiling, it is not moisture, but the life it brings that causes the greatest concern in the home environment. FACT: vapour causes 85% of residential damp problems.
Independence and Methodology
Our only income is through damp survey fees. We are independent of contractors and never profit from remedial work. We do not receive or pay any fees or other inducements. Our motivation is peace of mind and practical, durable solutions. We use an array of equipment to identify the root cause of damp within walls. Our damp surveys follow guidance from RICS, Historic England and PCA joint position statement and support RICS’s highest standard, level 3 “Home Survey Standard” (HSS).
During the survey we assess likelihood of rising damp*, mainswater leak, penetrating damp, condensation, timber rot and woodworm. We profile the damp patches and consider the likely sources of dampness and test ventilation against building regulations requirements. We consider changes to the property and factors just before the first sighting of damp.
- Rising damp concern: Clients concerned about rising damp
- Damp treatment: Despite the low risk of rising damp, disruption at the base of external walls suggests there has been an attempt at chemical treatment against rising damp. Internal plaster may have been replaced with damp proofers slurry. This can cause problems with absorption imbalance, resulting in increased condensation on other walls or vapour becoming absorbed and trapped behind the slurry.
- Weather: Inclement
- Property: Terraced Victorian house
- Background: Dampness in front bay corner, recent kitchen update
- Changes: Internal bathroom, inconsistent extractor fan use, double glazing to rear, new kitchen
- Occupancy: Family with special needs son
- Mould & notes: Mould in front corner, vapour trapped behind curtain
- Primary damp concern: Dampness in front bay
- Other damp concerns: Mould in bathroom
- Compounding: Heat loss from front bay
- Airbricks: Sufficient, front airbrick causing heat loss
- Sub-floor humidity: No concerns
- Tenure: House
- Attachment: Terraced
- Build: Victorian
- Walls: 9 inch
- Exterior comment: Overflowing water, blocked downpipe, no internal dampness
- Penetrating damp assessment: No concerns
- Drains: No concerns
- Leak signs: None
- Leak assessment: No leaks causing damp
- Floor: Suspended timber
- Loft: Not inspected
- Timber assessment: No structural concerns
- Last dry: Before kitchen renovation
- Ventilation assessment: Inadequate kitchen and bathroom fan use
W.H.O. indoor air quality guidelines
“Management of moisture requires proper control of temperature and ventilation to avoid excess humidity, condensation on surfaces and excess moisture in materials. Ventilation should be distributed effectively throughout spaces, and stagnant air zones should be avoided.”
FACT: Houses contain 30 – 40 litres of water as vapour typically. Each day, each occupant adds on average about 1.5 litres as follows:
- Each shower results in 1/2L condensing (each additional shower in a series won’t add as much as the first, so long as the door is kept closed)
- Vapour from drying clothes releases about ½ litre per day if dried indoors
- Respiration releases about ¾ litre per day (of which ¼ l at night)
- Cooking produces about ¼ litre per day per person
- Unvented vapour can cause condensation, mould and allergenic dust mites. The simple rule for keeping your property dry and mould free is;
- Vent out as much vapour as produced, each and every day!
- Central heating and double-glazing reduce background ventilation. To overcome this you should use mechanical extractors. Where properties are rented, consider using monitoring devices (such as a Govee WIFI hygrometer) and if necessary, install continuous flow extractors, but beware there can be a thermal cost caused by continuous heat lost.
FACTS about Condensation and Mould
- FACT: warm air holds more water vapour than cold air. The warmer it is, the more air’s capacity to hold water vapour. Conversely the colder it is, the less capacity, until air cannot hold any more vapour. We call that the dew point or 100%RH. As soon air reaches capacity, condensation will form on the coldest surfaces.
- FACT: Mould and dust mites
- FACT: Mould only grows when air is humid for long periods. In the occupied home environment, it is 6 hours over 85% RH. For properties that are unoccupied for long periods, it is 75% RH for many days of consistent and high humidity. Avoid allowing the surface relative humidity of cold walls to exceed 85% RH by ventilating, dehumidifying, insulating, and ensuring airflow, particularly in cold corners, base of walls and ceilings, eaves, and cold window and door reveals.
- FACT: Dust mites are microscopic insects that can cause allergies. They grow in similar conditions to mould. So ventilate more to avoid allergies.
- FACT: Health concerns: There are no health and safety issues from damp noted. It is in the occupier’s interests to keep a property properly ventilated or dehumidified and temperatures above the dew and mould points throughout the property, thereby reducing the health risk associated with dust mites, bacteria, protozoans, as well as decorative spoiling caused by mould.
TIPS To Stay Condensation and Mould Free
- TIP: Reduce the production of vapour at source:
- TIP: Keep bathroom extractor fans running, or window open for at least 30 minutes.
- TIP: Keep bathroom doors closed at all times, and bathroom windows open safely.
- TIP: When filling the bath, run the cold water first then add the hot.
- TIP: Dry clothes outside, in a dryer, in a closed room with a dehumidifier or window open, never on radiators or heated rail without a door closed and a means of removing the vapour.
- TIP: Cook with tops on pots and pans, avoiding excessive boiling.
- TIP: Keep the kitchen door closed and extractor fan on where possible.
- TIP:Mechanical vents are best, but if you only have passive vents, such as a whole in the wall or chimney, then vents open with space for air to move, insulate where possible.
- TIP: Keep trickle vents open or alternatively, open windows on safety locks.
- TIP: Stop mould forming:
* Maintain external wall temperatures above 12°C, with low background heating.
* Declutter leaving space for warm air to circulate around cold surfaces.
* Where possible, avoid placing wardrobes and furniture against external walls.
* Avoid overfilling wardrobes and cupboards as it restricts air circulation.
* Use dehumidifiers or small wardrobe dehumidifying bags and replace regularly.
* Wipe mould and condensation off walls and clothes as soon as it appears. - TIP: Monitor relative humidity
* We recommend monitoring temperature and relative humidity with a data logger to see what is happening.
