Data loggers – awaited
The report is completed after the data from your loggers is received 7 days after the survey. Things to focus on before sending data loggers.
- Improve ventilation by running the bathroom extractor fan or keeping the window open for at least 30 minutes after a shower, with the bathroom door kept closed, at least until the bathroom is dry. This will force warm dry air from the property into the bathroom, speeding up the drying of the bathroom, without allow vapour to diffused, like smoke does, back into the property.
- Don’t dry clothes internally without a dehumidifier or drying in a vented room, such as the bathroom, with the door closed.
- Cook with tops on pots and pans, use the kitchen extractor fan if you have one, or window open and door closed.
- Make sure the surface relative humidity in the coldest section of wall is above 85%RH. Consider insulating a wall if the internal temperature is not greater than 3°C when it is cold outside.
- In a well ventilated property the overall dew point should be at or below the outside dew point, ideally 3°C below the outside temperature. This is complex, see below.
See monitor-humidity-with-data-loggers on how to use the data logger app. To work out the external dew point, you can install a logger outside and look at the dew points indicated on the logger app (for example SensorBlue), or as a rough guide if you pick up the Met Weather, look up your area, then take the external temperature and external relative humidity then take off 1° for each 5% below 100%RH to estimate the dew point. So for instance if the external temperature is 14°C and humidity 80%, as a rough calculation, the external dew point is about 14-(100-80)/5 = 10°C.
Evidence & Illustrations
The chimney is acting as a thermal fin drawing heat out. It is also composed of a single skin of bricks surround a cold flue, unlike a normal wall which is two skins thick.
The flaunching is often incorrectly blames for dampness surrounding chimneys.
You ave exposed bricks next to a wall with coating. The coating will stop water evaporating out, causing marginal dampness on the outside. A wet brick is a poor insulator increasing the risk of condensation. rain is however, not penetrating through. In addition you have the chimney above.
other matters
To keep the property dry | |
|---|---|
| Target vapour from bathroom | |
| TIP: Keep the bathroom door closed with the fan running or window open until the humidity from the shower has subsided – typically at least 30 mins after the last shower. | |
| Target vapour from clothes drying | |
| Use a tumble dryer (like a heat pump), dry in a vented room with the door closed (possibly a bathroom with the extractor running or window open), or use a powerful dehumidifier. Don’t dry clothes in an unventilated room. | |
| Target vapour from cooking with an extractor fan | |
| Use the kitchen extractor fan whenever cooking. | |
| Use fan to expedite drying | |
| Direct a fan onto the damp patch to speed up the drying process. | |
| Maintain airflow close to cold walls | |
| TIP: Keep objects away from walls where condensation or mould has built up. Consider insulating cold internal surfaces, for example, with floor insulation from B&Q or Wallrock Thermal Liner (ensure to use Wallrock Thermal Liner Adhesive). | |
| Remove mould | |
| Consider sanding down mould where dry, and removing it with either bleach or anti-mould foam. I personally use HG Mould Remover Foam Spray, but imagine there is no major difference between brands. | £100 |
| Remedial actions – estimate of costs | £100 |
Actions if all else fails | |
|---|---|
| Consider using a dehumidifier | |
| Maintain relative humidity, especially at night when it’s cold outside, with a dehumidifier such as PureMate 20L/Day Portable & Compact Dehumidifier with 6.5 Litre (£179.99 Refrigerant), Duux Bora Smart Dehumidifier (DXDH02UK £300 Refrigerant) or Meaco DD8L Zambezi (£260 Desiccant – best for colder environments) – Which! Best buys. There are plenty of alternatives available. I choose a dehumidifier based on daily and tank capacity, low noise, whether it has a pipe out, and ease of programmable functions over other considerations such as weight and aesthetics. The technology is old and easy to manufacture. So if these brands are not available, you are sure to find another alternative. Evaluate based on daily capacity (20L minimum) and whether it has a continuous pipe out (use this to drip into a sink when away in winter). | £180 |
| Consider insulating cupboard | |
| Wood fibre insulation or similar stuck to the external cupboard wall can significantly reduce the risk of mould. | £100 |
| Consider targeted insulation on cold wall | |
| Consider installing thermal insulating plasterboard or thermal lining paper, such as wallrock thermal liner or Sempatap thermal solid wall insulation to cold surfaces. | £1,000 |
| Optimal actions – estimate of costs | £1,280 |
I conclude that excess vapour from ensuite bath with poor ducting out and probable bathroom door left open because it’s a sliding door, made worse by the cold chimney breast.
The proximity of vapour from the ensuite bathroom hitting a cold wall will result in high humidity, causing condensation, and in the case of the cupboard, mould from poor airflow.
Improved the bathroom extractor fan, which had an issue with the backdraught shutter being trapped by the ducting.. By taking a root cause approach, rather than a focus on blocking the symptoms of damp the savings are likely to be around £5,000. This contrasts with typical damp proofing contractor recommendations such as chemical treatment for rising damp and untargeted ventilation, such as PIV systems.
Flood risk: No risk See Flood Risk (note most flood risk is not from groundwater).
Sub-soil rocks: Rocks with essentially no groundwater See British Geological Survey.
Therefore risk of Rising Damp: remote possibility, see explanation by Dr Robyn Pender of Historic England.
I confirm that I inspected the property on 231027SH1200. I conclude that excess vapour from ensuite bath with poor ducting out and probable bathroom door left open because it’s a sliding door, made worse by the cold chimney breast.. All buildings can be exposed to unvented vapour and external dampness to some degree. You will mitigate the risk of damp if you follow all our recommendations. This report is intended to be read in full including supplementary links in this report. Observations and opinions must not be taken in isolation. Given the right weather conditions almost any house can be affected by rain. Like any building, you need to be aware of the risks of damp arising in the future and should plan a programme of monitoring, prevention and maintenance accordingly. Damp Surveys Ltd reports are designed to provide you with an informed, independent expert opinion as to the cause of dampness in the property, together with any recommendations for further investigation or remedial work. We do not warrant any findings in this report unless we enter into a separate warranty agreement with you.
The survey was conducted during daylight hours. Damp will be more noticeable at night and when the weather is colder and more humid. Gutters are more likely to fail when full of leaves and during periods of prolonged rain and adverse wind. We make best endeavours but cannot guarantee being able to identify all forms of damp, rot and insect infestation affecting the property.
We carried out a careful and thorough inspection of as much of the property as was accessible. However, when a full inspection is not possible, we make a professional judgement regarding the likelihood of a defect being present. In certain circumstances, this may lead to a recommendation for further action to open up an area for additional investigation. We were unable to inspect the entire roof, all the guttering, and some of the drains. Similarly, inspection of woodwork or other parts of the structure that were covered, unexposed, poorly lit or inaccessible such as in the loft, cellar, or sub-floor void was not possible, and therefore we are unable to assert that such parts of the property are free from defect. There were no obvious signs of damp resulting from these limitations
Negligence claims must be made within 90 days of the damp survey site visit. Clients must make best endeavours to monitor humidity and temperature on a damp wall and the closest source of humidity, by purchasing and placing two data loggers for example the Smart Hygrometer measuring humidity on the wall and nearest source of vapour, before and after following our recommendations. These data loggers have sufficient memory capacity to store 90 days of data.
This report is for the sole use of the client (named on the invoice, but omitted here for anonymity) for whom the survey was undertaken and can only be relied upon for 90 days from the survey date. Unless expressly stated otherwise in this report, nothing in this report confers or is intended to confer any rights on any third party pursuant to the Contracts (Rights of Third Parties) Act 1999.
Simon Hichens
Site visit 231027SH1200
Simon Hichens BSc Chemistry RICS Qualified Expert Witness (Chartered Surveyors)
PCA Certificated Surveyor of Dampness & Timber in Buildings (Property Care Association)
Damp Surveys Ltd, 119 Longton Ave London SE26 6RF Reg. 10977488 (England & Wales)
Founder of damp.aï & Member of the Society for the Protection of Ancient Buildings (SPAB)
Our damp surveys are designed to provide a holistic diagnosis that identifies and deals with causes rather than a focus on symptoms. Symptoms will disappear over time, once damp is stopped at source. We look for risks of dampness, but unless moisture is present, we can’t guarantee to identify all risks of future moisture. Our reports:
- identify root cause(s) of major unwanted dampness within the property,
- identify major symptoms of unwanted dampness,
- identify major structural damage caused by dampness,
- recommend actions and estimated costs to stop damp at source and mitigate its effects,
- recognise that treating damp is often a staged approach, treating obvious causes first.
Understanding damp
For survey purposes, damp is defined as unwanted water. Water brings life. We need it. Unfortunately, fungus and insects also thrive in water. While a damp wall can cause decorative spoiling, it is not moisture, but the life it brings that causes the greatest concern in the home environment. FACT: vapour causes 85% of residential damp problems.
Independence and Methodology
Our only income is through damp survey fees. We are independent of contractors and never profit from remedial work. We do not receive or pay any fees or other inducements. Our motivation is peace of mind and practical, durable solutions. We use an array of equipment to identify the root cause of damp within walls. Our damp surveys follow guidance from RICS, Historic England and PCA joint position statement and support RICS’s highest standard, level 3 “Home Survey Standard” (HSS).
During the survey we assess likelihood of rising damp*, mainswater leak, penetrating damp, condensation, timber rot and woodworm. We profile the damp patches and consider the likely sources of dampness and test ventilation against building regulations requirements. We consider changes to the property and factors just before the first sighting of damp.
- Rising damp concern: You were concerned about mould and condensation.
- Weather: Sunny, 14°C, 75% relative humidity.
- Property: 1920s or 30s semi-detached house.
- Background: Property purchased about a year ago.
- Changes: New bathroom upstairs, ensuite changes to the ground floor.
- Occupancy: Young family.
- Mould & notes: Mould on the cupboard wall in the master bedroom.
- Primary damp concern: In the master bedroom on the right-hand flank wall.
- Compounding: Heat loss created by the chimney breast.
- Airbricks: There is no reason to be concerned about the sub-floor ventilation.
- Sub-floor humidity: There were no concerns about humidity in the sub-floor void.
- Tenure: house
- Attachment: a semi-detached
- Build: 1920’s or 30’s
- Walls: 9-inch, probably not cavity.
- Exterior comment: No specific concerns.
- Penetrating damp assessment: The exterior appeared to be OK from a damp perspective. There are no obvious signs of significant penetrating damp.
- Drains: No specific concern.
- Leak signs: No specific concern.
- Leak assessment: There are no obvious signs of a significant mains or wastewater leak.
- Floor: No specific concern.
- Loft: Newly insulated, no signs of timber issues.
- Timber assessment: There are no suspicions of significant timber decay.
- Last dry: Probably dry when property purchased.
- Ventilation assessment: The. bathroom ventilation is insufficient, I double the throughflow of both bathrooms during the survey.
W.H.O. indoor air quality guidelines
“Management of moisture requires proper control of temperature and ventilation to avoid excess humidity, condensation on surfaces and excess moisture in materials. Ventilation should be distributed effectively throughout spaces, and stagnant air zones should be avoided.”
FACT: Houses contain 30 – 40 litres of water as vapour typically. Each day, each occupant adds on average about 1.5 litres as follows:
- Each shower results in 1/2L condensing (each additional shower in a series won’t add as much as the first, so long as the door is kept closed)
- Vapour from drying clothes releases about ½ litre per day if dried indoors
- Respiration releases about ¾ litre per day (of which ¼ l at night)
- Cooking produces about ¼ litre per day per person
- Unvented vapour can cause condensation, mould and allergenic dust mites. The simple rule for keeping your property dry and mould free is;
- Vent out as much vapour as produced, each and every day!
- Central heating and double-glazing reduce background ventilation. To overcome this you should use mechanical extractors. Where properties are rented, consider using monitoring devices (such as a Govee WIFI hygrometer) and if necessary, install continuous flow extractors, but beware there can be a thermal cost caused by continuous heat lost.
FACTS about Condensation and Mould
- FACT: warm air holds more water vapour than cold air. The warmer it is, the more air’s capacity to hold water vapour. Conversely the colder it is, the less capacity, until air cannot hold any more vapour. We call that the dew point or 100%RH. As soon air reaches capacity, condensation will form on the coldest surfaces.
- FACT: Mould and dust mites
- FACT: Mould only grows when air is humid for long periods. In the occupied home environment, it is 6 hours over 85% RH. For properties that are unoccupied for long periods, it is 75% RH for many days of consistent and high humidity. Avoid allowing the surface relative humidity of cold walls to exceed 85% RH by ventilating, dehumidifying, insulating, and ensuring airflow, particularly in cold corners, base of walls and ceilings, eaves, and cold window and door reveals.
- FACT: Dust mites are microscopic insects that can cause allergies. They grow in similar conditions to mould. So ventilate more to avoid allergies.
- FACT: Health concerns: There are no health and safety issues from damp noted. It is in the occupier’s interests to keep a property properly ventilated or dehumidified and temperatures above the dew and mould points throughout the property, thereby reducing the health risk associated with dust mites, bacteria, protozoans, as well as decorative spoiling caused by mould.
TIPS To Stay Condensation and Mould Free
- TIP: Reduce the production of vapour at source:
- TIP: Keep bathroom extractor fans running, or window open for at least 30 minutes.
- TIP: Keep bathroom doors closed at all times, and bathroom windows open safely.
- TIP: When filling the bath, run the cold water first then add the hot.
- TIP: Dry clothes outside, in a dryer, in a closed room with a dehumidifier or window open, never on radiators or heated rail without a door closed and a means of removing the vapour.
- TIP: Cook with tops on pots and pans, avoiding excessive boiling.
- TIP: Keep the kitchen door closed and extractor fan on where possible.
- TIP:Mechanical vents are best, but if you only have passive vents, such as a whole in the wall or chimney, then vents open with space for air to move, insulate where possible.
- TIP: Keep trickle vents open or alternatively, open windows on safety locks.
- TIP: Stop mould forming:
* Maintain external wall temperatures above 12°C, with low background heating.
* Declutter leaving space for warm air to circulate around cold surfaces.
* Where possible, avoid placing wardrobes and furniture against external walls.
* Avoid overfilling wardrobes and cupboards as it restricts air circulation.
* Use dehumidifiers or small wardrobe dehumidifying bags and replace regularly.
* Wipe mould and condensation off walls and clothes as soon as it appears. - TIP: Monitor relative humidity
* We recommend monitoring temperature and relative humidity with a data logger to see what is happening.
