Background
This Victorian house was bought a few years ago. Dampness are started appearing on the front wall as a brown stain.
Data loggers
In conclusion, from the data loggers
While there are seemingly few risks, you should monitor the internal dew point when it is cold outside, using ventilation and dehumidification to maintain a dew point below the outside temperature.
Evidence & Illustrations
There could be an aggravating factor, that could increase the dampness in bricks, increasing the risk of blistering and micro cracking….
To keep the property dry | |
|---|---|
| Trace and repair leak | |
| Trace the apparent loss in mainswater pressure between the street side and internal stopcocks. Because the leak appears to be coming from the road, I believe this is Thames Waters’ responsibility. For piece of mind, consider replacing the lead pipe all the way between the two stopcocks. | |
| Repaint external walls | |
| Wire brush paint on the external walls back to brick as much as possible, at least to remove the surface salts. It is better not to have paint, but if applying paint, use a paint that is as impermeable as any remaining paint, such as Zinsser or Dulux external masonry paint, using two coats and following the directions. | £1,000 |
| Improve sub-floor ventilation | |
| Consider installing a inline vent blowing air out of the sub-floor through an airbrick, a 2M length of rigid pipe (the same diameter as the fan) attached to the fan, can creating air-circulation. Block the sub-floor airbrick open to the kitchen – see other examples linked in the evidence section of this report. You may need an electrician to fit the vent. Ventilation will speed up the drying process and reduce the risk of rising damp like symptoms and rot. | £700 |
| Reduce vapour from cooking | |
| Cook with lids on pots and pans to reduce the production of vapour from cooking by 80%. | |
| Use a dehumidifier | |
| Maintain relative humidity, especially at night when it’s cold outside, with a dehumidifier such as the PureMate 20L/Day Portable & Compact Dehumidifier with 6.5 Litre (£179.99 Refrigerant), Duux Bora Smart Dehumidifier (DXDH02UK £300 Refrigerant), or Meaco DD8L Zambezi (£260 Desiccant – best for colder environments) – Which! Best Buys. There are plenty of alternatives available. I choose a dehumidifier based on daily and tank capacity, low noise, whether it has a pipe outlet, and ease of programmable functions over other considerations such as weight and aesthetics. The technology is old and easy to manufacture, so if these brands are not available, you are sure to find another alternative. Evaluate based on daily capacity (20L minimum) and whether it has a continuous pipe outlet (use this to drip into a sink when away in winter). A dehumidifier will save money compared to heating a property. Like an air source heat pump, for every £1 of energy spent on a dehumidifier, you get back roughly £1.50 of heat. Furthermore, when it’s cold, dry air feels warmer than humid air, so a dehumidifier will reduce energy consumption both when at home and away (as you don’t need to heat the house to stop mould). | £180 |
| Target vapour from clothes drying | |
| If needing to dry clothes inside, use a powerful dehumidifier (20 litres per day or more – see above) near the clothes dryer. Don’t dry clothes in an unventilated room and avoid heated clothes racks, as they can produce vapour at a faster rate than dehumidifiers can remove it. | |
| Monitor vapour with data loggers | |
| Monitor relative humidity and temperature against the damp wall or ceiling to observe the effects of improvements, such as the ORIA Wireless Thermometer Hygrometer (20m (2 Packs)) – already in place. Keep dew points (as seen at the base of each meter on the SensorBlue app) at or below the external temperature (which you can find on https://www.metoffice.gov.uk or https://www.bbc.co.uk/weather. Additionally, monitor improvements on the damp wall with a pencil line and damp meter such as the Dr. Wood moisture meter, logging improvements each month. | |
| Target vapour from bathroom | |
| Keep the bathroom doors closed with window open in the top floor bathroom and fan running in the first floor bathroom, until the humidity from the shower has subsided—typically at least 30 minutes after the last shower. Keeping vapour in the bathroom dramatically reduces the risk of mould and condensation elsewhere in the property but may increase the risk of mould in the bathroom, necessitating regular mould wipe-downs. Consider using a little HG Mould Remover Foam Spray on vulnerable areas such as cold zones and seals in the bathroom weekly. | |
| Remedial actions – estimate of costs | £1,880 |
Actions if all else fails | |
|---|---|
| If pooling continues | |
| If the water in the sub-floor does not disappear (stop polling), say four months after the leak is repaired, 1) ask Thames Water to check for a street side drain leak (checking issue found further up the road), 2) consider having a CCTV survey of your drains, 3) consider installing a sump-pump, first an area about 500mm cube should be dug, and the sump-pump used to pump water out from under the property, such as to a front drain. | £1,000 |
| Install kitchen extractor fan ducting | |
| Consider instructing a general builder to duct out kitchen extractor fan. The main challenge is getting the ducting from the extractor fan. Ideally the ducting should be using rigid ducting (for faster airflow, not flexible ducting as the ridges create eddies slowing air speed), as short as possible with as few bends. | £300 |
| Optimal actions – estimate of costs | £1,300 |
I conclude that the cause of internal dampness is a combination of rainwater absorbed through the external paint work causing penetrating damp and excess vapour from insufficient sub-floor ventilation and possibly internal ventilation in winter. There is a possibility of a mainswater leak, which needs to be checked by a plumber.
Rain is penetrating through micro cracks created by calcium sulphate salts, a key ingredient in cement, crystalising under the paint work. The root cause of this penetrating damp is almost certainly a mains water leak flowing into the sub-floor, probably from the street side stopcock.
. By taking a root cause approach, rather than a focus on blocking the symptoms of damp the savings are likely to be around £10,000. This contrasts with typical damp proofing contractor recommendations such as chemical treatment for rising damp and untargeted ventilation, such as PIV systems.
Flood risk: No risk See Flood Risk (note most flood risk is not from groundwater).
Sub-soil rocks: Rocks with essentially no groundwater See British Geological Survey.
Therefore risk of Rising Damp: remote possibility, see explanation by Dr Robyn Pender of Historic England.
I confirm that I inspected the property on 240523SH1200. I conclude that the cause of internal dampness is a combination of rainwater absorbed through the external paint work causing penetrating damp and excess vapour from insufficient sub-floor ventilation and possibly internal ventilation in winter. there is a possibility of . All buildings can be exposed to unvented vapour and external dampness to some degree. You will mitigate the risk of damp if you follow all our recommendations. This report is intended to be read in full including supplementary links in this report. Observations and opinions must not be taken in isolation. Given the right weather conditions almost any house can be affected by rain. Like any building, you need to be aware of the risks of damp arising in the future and should plan a programme of monitoring, prevention and maintenance accordingly. Damp Surveys Ltd reports are designed to provide you with an informed, independent expert opinion as to the cause of dampness in the property, together with any recommendations for further investigation or remedial work. We do not warrant any findings in this report unless we enter into a separate warranty agreement with you.
The survey was conducted during daylight hours. Damp will be more noticeable at night and when the weather is colder and more humid. Gutters are more likely to fail when full of leaves and during periods of prolonged rain and adverse wind. We make best endeavours but cannot guarantee being able to identify all forms of damp, rot and insect infestation affecting the property.
We carried out a careful and thorough inspection of as much of the property as was accessible. However, when a full inspection is not possible, we make a professional judgement regarding the likelihood of a defect being present. In certain circumstances, this may lead to a recommendation for further action to open up an area for additional investigation. We were unable to inspect the entire roof, all the guttering, and some of the drains. Similarly, inspection of woodwork or other parts of the structure that were covered, unexposed, poorly lit or inaccessible such as in the loft, cellar, or sub-floor void was not possible, and therefore we are unable to assert that such parts of the property are free from defect. There were no obvious signs of damp resulting from these limitations
Negligence claims must be made within 90 days of the damp survey site visit. Clients must make best endeavours to monitor humidity and temperature on a damp wall and the closest source of humidity, by purchasing and placing two data loggers for example the Smart Hygrometer measuring humidity on the wall and nearest source of vapour, before and after following our recommendations. These data loggers have sufficient memory capacity to store 90 days of data.
This report is for the sole use of the client (named on the invoice, but omitted here for anonymity) for whom the survey was undertaken and can only be relied upon for 90 days from the survey date. Unless expressly stated otherwise in this report, nothing in this report confers or is intended to confer any rights on any third party pursuant to the Contracts (Rights of Third Parties) Act 1999.
Simon Hichens
Site visit 240523SH1200
Simon Hichens BSc Chemistry RICS Qualified Expert Witness (Chartered Surveyors)
PCA Certificated Surveyor of Dampness & Timber in Buildings (Property Care Association)
Damp Surveys Ltd, 119 Longton Ave London SE26 6RF Reg. 10977488 (England & Wales)
Founder of damp.aï & Member of the Society for the Protection of Ancient Buildings (SPAB)
Our damp surveys are designed to provide a holistic diagnosis that identifies and deals with causes rather than a focus on symptoms. Symptoms will disappear over time, once damp is stopped at source. We look for risks of dampness, but unless moisture is present, we can’t guarantee to identify all risks of future moisture. Our reports:
- identify root cause(s) of major unwanted dampness within the property,
- identify major symptoms of unwanted dampness,
- identify major structural damage caused by dampness,
- recommend actions and estimated costs to stop damp at source and mitigate its effects,
- recognise that treating damp is often a staged approach, treating obvious causes first.
Understanding damp
For survey purposes, damp is defined as unwanted water. Water brings life. We need it. Unfortunately, fungus and insects also thrive in water. While a damp wall can cause decorative spoiling, it is not moisture, but the life it brings that causes the greatest concern in the home environment. FACT: vapour causes 85% of residential damp problems.
Independence and Methodology
Our only income is through damp survey fees. We are independent of contractors and never profit from remedial work. We do not receive or pay any fees or other inducements. Our motivation is peace of mind and practical, durable solutions. We use an array of equipment to identify the root cause of damp within walls. Our damp surveys follow guidance from RICS, Historic England and PCA joint position statement and support RICS’s highest standard, level 3 “Home Survey Standard” (HSS).
During the survey we assess likelihood of rising damp*, mainswater leak, penetrating damp, condensation, timber rot and woodworm. We profile the damp patches and consider the likely sources of dampness and test ventilation against building regulations requirements. We consider changes to the property and factors just before the first sighting of damp.
“Management of moisture requires proper control of temperature and ventilation to avoid excess humidity, condensation on surfaces and excess moisture in materials. Ventilation should be distributed effectively throughout spaces, and stagnant air zones should be avoided.”
FACT: Houses contain 30 – 40 litres of water as vapour typically. Each day, each occupant adds on average about 1.5 litres as follows:
- Each shower results in 1/2L condensing (each additional shower in a series won’t add as much as the first, so long as the door is kept closed)
- Vapour from drying clothes releases about ½ litre per day if dried indoors
- Respiration releases about ¾ litre per day (of which ¼ l at night)
- Cooking produces about ¼ litre per day per person
- Unvented vapour can cause condensation, mould and allergenic dust mites. The simple rule for keeping your property dry and mould free is;
- Vent out as much vapour as produced, each and every day!
- Central heating and double-glazing reduce background ventilation. To overcome this you should use mechanical extractors. Where properties are rented, consider using monitoring devices (such as a Govee WIFI hygrometer) and if necessary, install continuous flow extractors, but beware there can be a thermal cost caused by continuous heat lost.
FACTS about Condensation and Mould
- FACT: warm air holds more water vapour than cold air. The warmer it is, the more air’s capacity to hold water vapour. Conversely the colder it is, the less capacity, until air cannot hold any more vapour. We call that the dew point or 100%RH. As soon air reaches capacity, condensation will form on the coldest surfaces.
- FACT: Mould and dust mites
- FACT: Mould only grows when air is humid for long periods. In the occupied home environment, it is 6 hours over 85% RH. For properties that are unoccupied for long periods, it is 75% RH for many days of consistent and high humidity. Avoid allowing the surface relative humidity of cold walls to exceed 85% RH by ventilating, dehumidifying, insulating, and ensuring airflow, particularly in cold corners, base of walls and ceilings, eaves, and cold window and door reveals.
- FACT: Dust mites are microscopic insects that can cause allergies. They grow in similar conditions to mould. So ventilate more to avoid allergies.
- FACT: Health concerns: There are no health and safety issues from damp noted. It is in the occupier’s interests to keep a property properly ventilated or dehumidified and temperatures above the dew and mould points throughout the property, thereby reducing the health risk associated with dust mites, bacteria, protozoans, as well as decorative spoiling caused by mould.
TIPS To Stay Condensation and Mould Free
- TIP: Reduce the production of vapour at source:
- TIP: Keep bathroom extractor fans running, or window open for at least 30 minutes.
- TIP: Keep bathroom doors closed at all times, and bathroom windows open safely.
- TIP: When filling the bath, run the cold water first then add the hot.
- TIP: Dry clothes outside, in a dryer, in a closed room with a dehumidifier or window open, never on radiators or heated rail without a door closed and a means of removing the vapour.
- TIP: Cook with tops on pots and pans, avoiding excessive boiling.
- TIP: Keep the kitchen door closed and extractor fan on where possible.
- TIP:Mechanical vents are best, but if you only have passive vents, such as a whole in the wall or chimney, then vents open with space for air to move, insulate where possible.
- TIP: Keep trickle vents open or alternatively, open windows on safety locks.
- TIP: Stop mould forming:
* Maintain external wall temperatures above 12°C, with low background heating.
* Declutter leaving space for warm air to circulate around cold surfaces.
* Where possible, avoid placing wardrobes and furniture against external walls.
* Avoid overfilling wardrobes and cupboards as it restricts air circulation.
* Use dehumidifiers or small wardrobe dehumidifying bags and replace regularly.
* Wipe mould and condensation off walls and clothes as soon as it appears. - TIP: Monitor relative humidity
* We recommend monitoring temperature and relative humidity with a data logger to see what is happening.
What does the damp report say are the main causes of damp and main actions to stop damp?
¿Qué dice el informe de humedad sobre las principales causas de la humedad y las principales acciones para detenerla?
潮湿报告说什么是潮湿的主要原因和防止潮湿的主要措施？
नमी की रिपोर्ट के अनुसार नमी के मुख्य कारण और नमी को रोकने के लिए मुख्य कार्य क्या हैं?
Que dit le rapport sur l’humidité concernant les principales causes de l’humidité et les principales actions pour l’arrêter?
Was sagt der Feuchtigkeitsbericht über die Hauptursachen von Feuchtigkeit und die Hauptmaßnahmen zur Bekämpfung von Feuchtigkeit?
Что говорится в отчете о влажности о основных причинах влажности и основных действиях по ее устранению?
Cosa dice il rapporto sull’umidità riguardo le principali cause dell’umidità e le principali azioni per fermarla?