Background
A semi-detached terrace house, recently renovated, has been experiencing issues with dampness. Substantial renovations were completed in August, following which a few areas of damp have presented themselves.
Data loggers
In conclusion, from the data loggers
- You should aim to bring your internal dew point down to external temperatures with targeted ventilation and dehumidification, see dew point shown on each device, within the Sensor Blue app.
Evidence & Illustrations
Moisture dissolves calcium sulphate salts, one of the key ingredients in cement. In a similar way to salt erosion in nature, dissolved salts concentrate and crystallise under the paint causing micro cracks. Once micro-cracking occurs the speed at which the rain becomes absorbed increases self-perpetuating ingress.
The simple solution is to regularly check for defects, wire brush away any surface salts, and expect to repaint every 7 or so years.
I’m not a lawyer, however, even though the extension is built for your property, the wall appears to be on your neighbours side of the party wall and therefore the paint should be their responsibility. The top of the wall and cracks visible between the two properties may have initiated the paint damage. I would cover the top of the wall, such as with coping stones and fill any gaps higher up.
To keep the property dry | |
|---|---|
| Ask neighbour to paint external walls | |
| Wire brush the paint on the external walls back to brick, as much as possible at least to remove the surface salts. Then use a paint that is as impermeable, ideally the same as the existing paint, or more impermeable, such as Zinsser or Dulux external masonry paint. In addition, cover the top of the rea wall, such as with coping stones, fill all cracks, front and back, either with mastic or for larger cracks over 3mm with a cement based mortar. | £1,000 |
| Use a dehumidifier | |
| To manage relative humidity, especially when poorly ventilated, humid or cold, consider using a dehumidifier such as the PureMate 20L/Day Portable & Compact Dehumidifier with 6.5 Litre (£179.99 Refrigerant), Duux Bora Smart Dehumidifier (DXDH02UK £300 Refrigerant) or Meaco DD8L Zambezi (£260 Desiccant – optimal for colder environments) – all highly rated by Which!. There are numerous alternatives if these specific models are not available. When selecting a dehumidifier, prioritise factors like daily and tank capacity, low noise levels, the availability of a continuous drainage option, and ease of use for programming functions, over aesthetics and weight. The technology behind dehumidifiers is well-established and straightforward to produce, ensuring you can find a suitable alternative focusing on a minimum daily capacity of 20L and the presence of a continuous drainage feature. | £180 |
| Use fan to expedite drying | |
| Direct a fan towards any damp areas to expedite the drying process. | |
| Target vapour from bathroom | |
| After showering, keep the bathroom door closed and the window open or fan running for at least 30 minutes to allow vapour to dissipate. | |
| Target vapour from cooking | |
| Always use tops on pots and pans to reduce vapour emission by 80% and where applicable use an externally ducted kitchen extractor fan. | |
| Target vapour from clothes drying | |
| Opt for a tumble dryer, dry laundry in a well-ventilated room with the door closed (such as a bathroom with the extractor fan on or window open), or employ a sufficiently high capacity dehumidifier. Avoid drying clothes in poorly ventilated areas and anywhere near cold walls. | |
| Monitor improvements | |
| Mark improvements on damp walls with a pencil line or sticky note and use a moisture meter, such as the Dr. Meter Wood Moisture Meter 2 in 1 Pin & Pinless Multifunctional Water Detector £23.99 or similar damp meter, to log and monitor reduction to dampness in walls. By doing so, you will gain early confidence in these recommendations. Use devices like the ORIA Wireless Thermometer Hygrometer to monitor relative humidity and temperature near walls or ceilings, look to keep the dew point at or below the external temperature. The dew point is shown on the app (if not use https://mouldpoint.co.uk to calculate the dew point from humidity and temperature readings). | |
| Keep objects away from walls | |
| Reposition furniture and open curtains away from walls, to improve flow of air from the radiator to damp walls. | |
| Remedial actions – estimate of costs | £1,180 |
Actions if all else fails | |
|---|---|
| Consider targeted insulation | |
| After ensuring walls are dry and mould-free, consider insulating damp walls with vapour permeable wood fibre where not visible, such as inside the box in the extension, or thermal lining paper, such supplied by Rockwool, where visible | £200 |
| Optimal actions – estimate of costs | £200 |
I conclude that there is penetrating damp from your exposed brickwork on the neighbours side of the wall, made worse by excess internal humidity on your side.
the brown stain indicates that water is passing through building material. There are crack on your neighbours side in the vicinity of your damp patch.
I improve the bathroom extractor fan. By taking a root cause approach, rather than a focus on blocking the symptoms of damp the savings are likely to be around £10,000. This contrasts with typical damp proofing contractor recommendations such as chemical treatment for rising damp and untargeted ventilation, such as PIV systems.
Flood risk: No risk See Flood Risk (note most flood risk is not from groundwater).
Sub-soil rocks: Rocks with essentially no groundwater See British Geological Survey.
Therefore risk of Rising Damp: remote possibility, see explanation by Dr Robyn Pender of Historic England.
I confirm that I inspected the property on 240110SH1200. I conclude that there is penetrating damp from your exposed brickwork on the neighbours side of the wall, made worse by excess internal humidity on your side. All buildings can be exposed to unvented vapour and external dampness to some degree. You will mitigate the risk of damp if you follow all our recommendations. This report is intended to be read in full including supplementary links in this report. Observations and opinions must not be taken in isolation. Given the right weather conditions almost any house can be affected by rain. Like any building, you need to be aware of the risks of damp arising in the future and should plan a programme of monitoring, prevention and maintenance accordingly. Damp Surveys Ltd reports are designed to provide you with an informed, independent expert opinion as to the cause of dampness in the property, together with any recommendations for further investigation or remedial work. We do not warrant any findings in this report unless we enter into a separate warranty agreement with you.
The survey was conducted during daylight hours. Damp will be more noticeable at night and when the weather is colder and more humid. Gutters are more likely to fail when full of leaves and during periods of prolonged rain and adverse wind. We make best endeavours but cannot guarantee being able to identify all forms of damp, rot and insect infestation affecting the property.
We carried out a careful and thorough inspection of as much of the property as was accessible. However, when a full inspection is not possible, we make a professional judgement regarding the likelihood of a defect being present. In certain circumstances, this may lead to a recommendation for further action to open up an area for additional investigation. We were unable to inspect the entire roof, all the guttering, and some of the drains. Similarly, inspection of woodwork or other parts of the structure that were covered, unexposed, poorly lit or inaccessible such as in the loft, cellar, or sub-floor void was not possible, and therefore we are unable to assert that such parts of the property are free from defect. There were no obvious signs of damp resulting from these limitations
Negligence claims must be made within 90 days of the damp survey site visit. Clients must make best endeavours to monitor humidity and temperature on a damp wall and the closest source of humidity, by purchasing and placing two data loggers for example the Smart Hygrometer measuring humidity on the wall and nearest source of vapour, before and after following our recommendations. These data loggers have sufficient memory capacity to store 90 days of data.
This report is for the sole use of the client (named on the invoice, but omitted here for anonymity) for whom the survey was undertaken and can only be relied upon for 90 days from the survey date. Unless expressly stated otherwise in this report, nothing in this report confers or is intended to confer any rights on any third party pursuant to the Contracts (Rights of Third Parties) Act 1999.
Simon Hichens
Site visit 240110SH1200
Simon Hichens BSc Chemistry RICS Qualified Expert Witness (Chartered Surveyors)
PCA Certificated Surveyor of Dampness & Timber in Buildings (Property Care Association)
Damp Surveys Ltd, 119 Longton Ave London SE26 6RF Reg. 10977488 (England & Wales)
Founder of damp.aï & Member of the Society for the Protection of Ancient Buildings (SPAB)
Our damp surveys are designed to provide a holistic diagnosis that identifies and deals with causes rather than a focus on symptoms. Symptoms will disappear over time, once damp is stopped at source. We look for risks of dampness, but unless moisture is present, we can’t guarantee to identify all risks of future moisture. Our reports:
- identify root cause(s) of major unwanted dampness within the property,
- identify major symptoms of unwanted dampness,
- identify major structural damage caused by dampness,
- recommend actions and estimated costs to stop damp at source and mitigate its effects,
- recognise that treating damp is often a staged approach, treating obvious causes first.
Understanding damp
For survey purposes, damp is defined as unwanted water. Water brings life. We need it. Unfortunately, fungus and insects also thrive in water. While a damp wall can cause decorative spoiling, it is not moisture, but the life it brings that causes the greatest concern in the home environment. FACT: vapour causes 85% of residential damp problems.
Independence and Methodology
Our only income is through damp survey fees. We are independent of contractors and never profit from remedial work. We do not receive or pay any fees or other inducements. Our motivation is peace of mind and practical, durable solutions. We use an array of equipment to identify the root cause of damp within walls. Our damp surveys follow guidance from RICS, Historic England and PCA joint position statement and support RICS’s highest standard, level 3 “Home Survey Standard” (HSS).
During the survey we assess likelihood of rising damp*, mainswater leak, penetrating damp, condensation, timber rot and woodworm. We profile the damp patches and consider the likely sources of dampness and test ventilation against building regulations requirements. We consider changes to the property and factors just before the first sighting of damp.
- Rising damp concern: You were concern you might have rising damp.
- Damp treatment: Despite the low risk of rising damp, there has been an attempt at chemical treatment against rising damp. Rising damp treatment is normally a sign of insufficient ventilation. The walls have been drilled into by about 200mm and injected with damp proofing chemicals. In theory the chemicals are absorbed into the brick pores reducing the bricks ability to absorb moisture. Walls are replaced with damp proofers slurry. This can cause problems with absorption imbalance, resulting in increased condensation on other walls or vapour becoming absorbed and trapped behind the slurry. There was evidence of surface condensation in areas probably not treated with replacement plaster but no evidence of trapped vapour. The solution is through ventilation and humidity control.
- Weather: dry overcast
- Property: Victorian
- Changes: Extension to rear including new kitchen, loft extension and modern living
- Occupancy: owner occupiers
- Mould & notes: there is mould in various areas
- Primary damp concern: Dampness to the rear extension
- Other damp concerns: Dampness on the first floor
- Compounding: heat loss from poor insulation
- Airbricks: There is no reason to be concerned about the sub-floor ventilation.
- Sub-floor humidity: The sub-floor ventilation appears to be of no concern.
- Tenure: house
- Attachment: a semi-detached
- Build: Victorian
- Walls: solid wall made of two brick widths (225mm)
- Exterior comment: There are cracks on the neighbour’s side both front and back
- Penetrating damp assessment: The exterior appeared to be OK from a damp perspective. There are no obvious signs of significant penetrating damp.
- Drains: The drains are of no special concern.
- Leak signs: No suspicion of a mains water leak
- Leak assessment: There are no obvious signs of a significant mains or wastewater leak.
- Floor: The ground floor felt solid.
- Loft: The loft has been converted.
- Timber assessment: There are no suspicions of significant timber decay.
- Last dry: I understand that some damp issues were picked up when you bought, but these have become worse over time.
- Ventilation assessment: There is insufficient bathroom and kitchen ventilation
W.H.O. indoor air quality guidelines
“Management of moisture requires proper control of temperature and ventilation to avoid excess humidity, condensation on surfaces and excess moisture in materials. Ventilation should be distributed effectively throughout spaces, and stagnant air zones should be avoided.”
FACT: Houses contain 30 – 40 litres of water as vapour typically. Each day, each occupant adds on average about 1.5 litres as follows:
- Each shower results in 1/2L condensing (each additional shower in a series won’t add as much as the first, so long as the door is kept closed)
- Vapour from drying clothes releases about ½ litre per day if dried indoors
- Respiration releases about ¾ litre per day (of which ¼ l at night)
- Cooking produces about ¼ litre per day per person
- Unvented vapour can cause condensation, mould and allergenic dust mites. The simple rule for keeping your property dry and mould free is;
- Vent out as much vapour as produced, each and every day!
- Central heating and double-glazing reduce background ventilation. To overcome this you should use mechanical extractors. Where properties are rented, consider using monitoring devices (such as a Govee WIFI hygrometer) and if necessary, install continuous flow extractors, but beware there can be a thermal cost caused by continuous heat lost.
FACTS about Condensation and Mould
- FACT: warm air holds more water vapour than cold air. The warmer it is, the more air’s capacity to hold water vapour. Conversely the colder it is, the less capacity, until air cannot hold any more vapour. We call that the dew point or 100%RH. As soon air reaches capacity, condensation will form on the coldest surfaces.
- FACT: Mould and dust mites
- FACT: Mould only grows when air is humid for long periods. In the occupied home environment, it is 6 hours over 85% RH. For properties that are unoccupied for long periods, it is 75% RH for many days of consistent and high humidity. Avoid allowing the surface relative humidity of cold walls to exceed 85% RH by ventilating, dehumidifying, insulating, and ensuring airflow, particularly in cold corners, base of walls and ceilings, eaves, and cold window and door reveals.
- FACT: Dust mites are microscopic insects that can cause allergies. They grow in similar conditions to mould. So ventilate more to avoid allergies.
- FACT: Health concerns: There are no health and safety issues from damp noted. It is in the occupier’s interests to keep a property properly ventilated or dehumidified and temperatures above the dew and mould points throughout the property, thereby reducing the health risk associated with dust mites, bacteria, protozoans, as well as decorative spoiling caused by mould.
TIPS To Stay Condensation and Mould Free
- TIP: Reduce the production of vapour at source:
- TIP: Keep bathroom extractor fans running, or window open for at least 30 minutes.
- TIP: Keep bathroom doors closed at all times, and bathroom windows open safely.
- TIP: When filling the bath, run the cold water first then add the hot.
- TIP: Dry clothes outside, in a dryer, in a closed room with a dehumidifier or window open, never on radiators or heated rail without a door closed and a means of removing the vapour.
- TIP: Cook with tops on pots and pans, avoiding excessive boiling.
- TIP: Keep the kitchen door closed and extractor fan on where possible.
- TIP:Mechanical vents are best, but if you only have passive vents, such as a whole in the wall or chimney, then vents open with space for air to move, insulate where possible.
- TIP: Keep trickle vents open or alternatively, open windows on safety locks.
- TIP: Stop mould forming:
* Maintain external wall temperatures above 12°C, with low background heating.
* Declutter leaving space for warm air to circulate around cold surfaces.
* Where possible, avoid placing wardrobes and furniture against external walls.
* Avoid overfilling wardrobes and cupboards as it restricts air circulation.
* Use dehumidifiers or small wardrobe dehumidifying bags and replace regularly.
* Wipe mould and condensation off walls and clothes as soon as it appears. - TIP: Monitor relative humidity
* We recommend monitoring temperature and relative humidity with a data logger to see what is happening.
