Background
The building was previously occupied by a dry cleaners. Once they vacated, no damp was noticed. The building has since undergone a full refurbishment including two flats above. The shop where the damp has occurred was near completion (fully plastered and decorated) when damp on all party walls appeared. The contractor provided mechanical heaters and ventilation for two weeks which cleared the issue, although once the heaters were removed, the damp returned. The property is currently vacant following the refurbishment.
Data loggers – see damp.ai/detect
We set up the data loggers during the survey. A few days worth of data would be useful. You can upload and use damp.ai/detect, but note the analysis is designed for a residential and or occupied property use.
Evidence & Illustrations
Many walls including this external section has mould. Mould growth occurs where relative humidity exceeds 85%RH for more than six hours. Excessive humidity is usually due to insufficient ventilation, poor air circulation, and cold surfaces. Relative humidity measures the amount of vapour in the air relative to the air’s capacity to hold vapour. It is influenced by vapour pressureand temperature. As temperature rises, the air can hold more vapour. Conversely, as temperature drops, the air’s capacity to hold vapour decreases until it reaches the dew point at 100%RH, resulting in the formation of dew or condensation. A secondary cause of high relative humidity is a low temperature relative to the source of humidity. Mould growth is inhibited by nitrates found in groundwater. The presence of mould at the bottom of a wall rules out rising damp as the root cause and points towards condensation from unvented excess vapour.
To keep the property dry | |
|---|---|
| Repair leak | |
| The builder will know the best solution. However, if the plastic soil pipe is simply replaced like for like, without a rat resistant layer, then the rat and leak are likely to return. | £300 |
| Repair rainwater goods | |
| The builder seemed to understand the requirements. There are several rainwater-related defects, as shown in the video: 1) an overflowing pipe from the hopper (which should be adjusted to ensure proper flow), 2) a damaged wrought iron pipe (which should be repaired or, preferably, replaced), 3) a blocked gutter from the neighbouring property (which should be unblocked), and 4) a damaged or missing plinth at the base of the wall (which should be enhanced with a cement-based mortar up to 1 metre). It is advisable to have someone inspect the rainwater goods during a rainstorm to identify any further issues and carry out the necessary repairs. | £1,000 |
| Use fan to expedite drying | |
| Direct a fan onto the damp patch to speed up the drying process. | |
| Use a dehumidifier | |
| Maintain relative humidity, especially at night when it’s cold outside, with a dehumidifier such as PureMate 20L/Day Portable & Compact Dehumidifier with 6.5 Litre (£179.99 Refrigerant), Duux Bora Smart Dehumidifier (DXDH02UK £300 Refrigerant) or Meaco DD8L Zambezi (£260 Desiccant – best for colder environments) – Which! Best buys. There are plenty of alternatives available. I choose a dehumidifier based on daily and tank capacity, low noise, whether it has a pipe out, and ease of programmable functions over other considerations such as weight and aesthetics. The technology is old and easy to manufacture. So if these brands are not available, you are sure to find another alternative. Evaluate based on daily capacity (20L minimum) and whether it has a continuous pipe out (use this to drip into a sink when away in winter). | £180 |
| Monitor dampness in wall | |
| Monitor improvements on the damp wall with a pencil line and or damp meter such as dr.wood moisture meter, logging improvements each month. | |
| Follow Dew’s Law | |
| Follow Dew’s Law to effectively manage internal vapour, it is crucial to maintain the internal vapour levels, as measured by the dew point in degrees Centigrade, below the external temperature. This can be achieved through adequate ventilation and the use of dehumidifiers. Monitor the internal Dew Point with a reliable device, such as the Habotest Hygrometer or Dew Point Meter HT607, or utilise the sensorblue app paired with the ORIA Wireless Thermometer Hygrometer. These tools help in accurately gauging humidity levels, ensuring they remain optimal. For more detailed information on detecting and managing damp issues, please visit https://damp.ai/detect. Although vapour levels were not excessive during the monitored period, it is essential to prepare for the colder months when the risk of condensation is at its greatest. | |
| Mould Removal | |
| When mould is dry, consider sanding it down and removing it with bleach or anti-mould foam. While I personally recommend HG Mould Remover Foam Spray, the effectiveness between brands is likely similar. | |
| Forward planning – occupiers | |
| I would replace the current extractor fan with a quiet continuous flow fan, such as a 5 litre per second bathroom size fan e.g. Vent-Axia Silent Continuous Running Bathroom Extractor Fan 100mm – Humidistat & Timer 479089. In addition I would make it the tenants responsibility to ensure the fan is running and monitor internal humidity, using a dehumidifier at night if internal vapour, as measured by dew point, is above the external temperature – following Dew’s Law. | |
| Remedial actions – estimate of costs | £1,480 |
Actions if all else fails | |
|---|---|
| Consider installing thermal insulated plasterboard | |
| Consider installing thermal insulated plasterboard on cold external walls. Until the flat above is occupied, the corridor should be considered external. Insulation is not a substitute for stopping penetrating damp, leaks and occupiers maintaining normal levels of internal vapour through ventilation and dehumidification, but it will act as a ‘belt and braces’ solution against condensation. It will also prevent hygroscopic salts from passing through the infused brickwork. Make sure the plaster does not touch the solid floor. The solutions below are instead of installing thermal insulating plasterboard. | £4,000 |
| Consider using absorption reducing chemicals | |
| For walls above a solid floor, remove the skirting board at the base of the wall and cut the lowest 10 – 20mm of plaster back to brick. Then run a ~10mm thick bead of Silane/Siloxane thixotropic cream, such as DryZone by Safeguard, along the brick to reduce absorption. Replace the skirting board. This is not instead of other remedial actions. I don’t advocate drilling holes and injecting chemicals, as you could damage the wall and be held responsible for causing damp in your neighbour’s property, with or without the necessary party wall agreement. Likewise, I don’t advocated replacing plaster with slurry, unless you are unable to stop water at its source. Make sure that plaster and plasterboard does not touch the solid floor to reduce the risk of condensation rising up the absorbent surface. | £1,000 |
| Hygroscopic salts – rear flank wall | |
| Hygroscopic salts may resemble grease stains but rest assured, they’re harmless. They don’t cause damage or mould, yet can appear unsightly, especially during summer heatwaves, potentially complicating property sales or rentals. Keep this report handy to reassure prospective buyers of their benign nature. Effective Solutions: The prime method to conceal these salts involves an impermeable blocker with at least 300mm overlap, preventing the spread of any damp appearance. Aim for a uniform treatment across wall sections to ensure consistent humidity interaction. Remember, these salts often lurk just below the surface. Cost-Effective Remediation Methods: Zinsser Cover Stain: The simplest, most affordable approach. Two coats of this solvent-based primer-sealer should do the trick, costing about £15 plus potential labour. It’s user-friendly, easy to remove and reapply, making it ideal for DIY fixes. For larger areas, consider a gloss paint layer between two Zinsser coats for uniformity. This is a homeowner-friendly task but can also be efficiently tackled by a builder as part of a bigger project. Sempatap/Wallrock: Ideal for mildly cold walls, this lining paper creates a barrier, offering slight insulation. It’s a half-day job costing about £100 per linear metre. Thermal Insulating Plasterboard: For very cold walls, removing plaster and installing this board with a vapour barrier is best, mirroring professional damp proofing. It’s a day-long task, costing around £400 per linear metre. Note on Damp Proofing Slurry: Often less effective, as it can activate salts, it’s also invasive and costly. Starting Point: Zinsser Cover Stain is your go-to. It’s budget-friendly and effective for immediate action, with the option to escalate to plasterboard installation if necessary. Humidity Management: Excessive humidity can highlight salts at the impermeable material’s edge. If this happens, a second Zinsser application is recommended. | £300 |
| Optimal actions – estimate of costs | £5,300 |
I conclude that the primary cause of internal dampness in is penetrating damp from an pipe that is flowing over the rear hopper, and related issues, made worse by excess vapour from insufficient ventilation, heating or dehumidification, a recent leak from the upstairs toilet and probable hygroscopic salts (although you can’t be sure until you have run a dehumidifier and fan for a while). .
In a humid environment, without leaks, water moves mainly through vapour diffusion.
. By taking a root cause approach, rather than a focus on blocking the symptoms of damp the savings are likely to be around £10,000. This contrasts with typical damp proofing contractor recommendations such as chemical treatment for rising damp and untargeted ventilation, such as PIV systems.
Flood risk: No risk See Flood Risk (note most flood risk is not from groundwater).
Sub-soil rocks: Rocks with essentially no groundwater See British Geological Survey.
Therefore risk of Rising Damp: remote possibility, see explanation by Dr Robyn Pender of Historic England.
I confirm that I inspected the property on 240805SH0800. I conclude that the primary cause of internal dampness in is penetrating damp from an pipe that is flowing over the rear hopper, and related issues, made worse by excess vapour from insufficient ventilation, heating or dehumidification, a recent leak from the upstairs toi. All buildings can be exposed to unvented vapour and external dampness to some degree. You will mitigate the risk of damp if you follow all our recommendations. This report is intended to be read in full including supplementary links in this report. Observations and opinions must not be taken in isolation. Given the right weather conditions almost any house can be affected by rain. Like any building, you need to be aware of the risks of damp arising in the future and should plan a programme of monitoring, prevention and maintenance accordingly. Damp Surveys Ltd reports are designed to provide you with an informed, independent expert opinion as to the cause of dampness in the property, together with any recommendations for further investigation or remedial work. We do not warrant any findings in this report unless we enter into a separate warranty agreement with you.
The survey was conducted during daylight hours. Damp will be more noticeable at night and when the weather is colder and more humid. Gutters are more likely to fail when full of leaves and during periods of prolonged rain and adverse wind. We make best endeavours but cannot guarantee being able to identify all forms of damp, rot and insect infestation affecting the property.
We carried out a careful and thorough inspection of as much of the property as was accessible. However, when a full inspection is not possible, we make a professional judgement regarding the likelihood of a defect being present. In certain circumstances, this may lead to a recommendation for further action to open up an area for additional investigation. We were unable to inspect the entire roof, all the guttering, and some of the drains. Similarly, inspection of woodwork or other parts of the structure that were covered, unexposed, poorly lit or inaccessible such as in the loft, cellar, or sub-floor void was not possible, and therefore we are unable to assert that such parts of the property are free from defect. There were no obvious signs of damp resulting from these limitations
Negligence claims must be made within 90 days of the damp survey site visit. Clients must make best endeavours to monitor humidity and temperature on a damp wall and the closest source of humidity, by purchasing and placing two data loggers for example the Smart Hygrometer measuring humidity on the wall and nearest source of vapour, before and after following our recommendations. These data loggers have sufficient memory capacity to store 90 days of data.
This report is for the sole use of the client (named on the invoice, but omitted here for anonymity) for whom the survey was undertaken and can only be relied upon for 90 days from the survey date. Unless expressly stated otherwise in this report, nothing in this report confers or is intended to confer any rights on any third party pursuant to the Contracts (Rights of Third Parties) Act 1999.
Simon Hichens
Site visit 240805SH0800
Simon Hichens BSc Chemistry RICS Qualified Expert Witness (Chartered Surveyors)
PCA Certificated Surveyor of Dampness & Timber in Buildings (Property Care Association)
Damp Surveys Ltd, 119 Longton Ave London SE26 6RF Reg. 10977488 (England & Wales)
Founder of damp.aï & Member of the Society for the Protection of Ancient Buildings (SPAB)
Our damp surveys are designed to provide a holistic diagnosis that identifies and deals with causes rather than a focus on symptoms. Symptoms will disappear over time, once damp is stopped at source. We look for risks of dampness, but unless moisture is present, we can’t guarantee to identify all risks of future moisture. Our reports:
- identify root cause(s) of major unwanted dampness within the property,
- identify major symptoms of unwanted dampness,
- identify major structural damage caused by dampness,
- recommend actions and estimated costs to stop damp at source and mitigate its effects,
- recognise that treating damp is often a staged approach, treating obvious causes first.
Understanding damp
For survey purposes, damp is defined as unwanted water. Water brings life. We need it. Unfortunately, fungus and insects also thrive in water. While a damp wall can cause decorative spoiling, it is not moisture, but the life it brings that causes the greatest concern in the home environment. FACT: vapour causes 85% of residential damp problems.
Independence and Methodology
Our only income is through damp survey fees. We are independent of contractors and never profit from remedial work. We do not receive or pay any fees or other inducements. Our motivation is peace of mind and practical, durable solutions. We use an array of equipment to identify the root cause of damp within walls. Our damp surveys follow guidance from RICS, Historic England and PCA joint position statement and support RICS’s highest standard, level 3 “Home Survey Standard” (HSS).
During the survey we assess likelihood of rising damp*, mainswater leak, penetrating damp, condensation, timber rot and woodworm. We profile the damp patches and consider the likely sources of dampness and test ventilation against building regulations requirements. We consider changes to the property and factors just before the first sighting of damp.
- Rising damp concern: You were concern you might have rising damp.
“Management of moisture requires proper control of temperature and ventilation to avoid excess humidity, condensation on surfaces and excess moisture in materials. Ventilation should be distributed effectively throughout spaces, and stagnant air zones should be avoided.”
FACT: Houses contain 30 – 40 litres of water as vapour typically. Each day, each occupant adds on average about 1.5 litres as follows:
- Each shower results in 1/2L condensing (each additional shower in a series won’t add as much as the first, so long as the door is kept closed)
- Vapour from drying clothes releases about ½ litre per day if dried indoors
- Respiration releases about ¾ litre per day (of which ¼ l at night)
- Cooking produces about ¼ litre per day per person
- Unvented vapour can cause condensation, mould and allergenic dust mites. The simple rule for keeping your property dry and mould free is;
- Vent out as much vapour as produced, each and every day!
- Central heating and double-glazing reduce background ventilation. To overcome this you should use mechanical extractors. Where properties are rented, consider using monitoring devices (such as a Govee WIFI hygrometer) and if necessary, install continuous flow extractors, but beware there can be a thermal cost caused by continuous heat lost.
FACTS about Condensation and Mould
- FACT: warm air holds more water vapour than cold air. The warmer it is, the more air’s capacity to hold water vapour. Conversely the colder it is, the less capacity, until air cannot hold any more vapour. We call that the dew point or 100%RH. As soon air reaches capacity, condensation will form on the coldest surfaces.
- FACT: Mould and dust mites
- FACT: Mould only grows when air is humid for long periods. In the occupied home environment, it is 6 hours over 85% RH. For properties that are unoccupied for long periods, it is 75% RH for many days of consistent and high humidity. Avoid allowing the surface relative humidity of cold walls to exceed 85% RH by ventilating, dehumidifying, insulating, and ensuring airflow, particularly in cold corners, base of walls and ceilings, eaves, and cold window and door reveals.
- FACT: Dust mites are microscopic insects that can cause allergies. They grow in similar conditions to mould. So ventilate more to avoid allergies.
- FACT: Health concerns: There are no health and safety issues from damp noted. It is in the occupier’s interests to keep a property properly ventilated or dehumidified and temperatures above the dew and mould points throughout the property, thereby reducing the health risk associated with dust mites, bacteria, protozoans, as well as decorative spoiling caused by mould.
TIPS To Stay Condensation and Mould Free
- TIP: Reduce the production of vapour at source:
- TIP: Keep bathroom extractor fans running, or window open for at least 30 minutes.
- TIP: Keep bathroom doors closed at all times, and bathroom windows open safely.
- TIP: When filling the bath, run the cold water first then add the hot.
- TIP: Dry clothes outside, in a dryer, in a closed room with a dehumidifier or window open, never on radiators or heated rail without a door closed and a means of removing the vapour.
- TIP: Cook with tops on pots and pans, avoiding excessive boiling.
- TIP: Keep the kitchen door closed and extractor fan on where possible.
- TIP:Mechanical vents are best, but if you only have passive vents, such as a whole in the wall or chimney, then vents open with space for air to move, insulate where possible.
- TIP: Keep trickle vents open or alternatively, open windows on safety locks.
- TIP: Stop mould forming:
* Maintain external wall temperatures above 12°C, with low background heating.
* Declutter leaving space for warm air to circulate around cold surfaces.
* Where possible, avoid placing wardrobes and furniture against external walls.
* Avoid overfilling wardrobes and cupboards as it restricts air circulation.
* Use dehumidifiers or small wardrobe dehumidifying bags and replace regularly.
* Wipe mould and condensation off walls and clothes as soon as it appears. - TIP: Monitor relative humidity
* We recommend monitoring temperature and relative humidity with a data logger to see what is happening.
What does the damp report say are the main causes of damp and main actions to stop damp?
¿Qué dice el informe de humedad sobre las principales causas de la humedad y las principales acciones para detenerla?
潮湿报告说什么是潮湿的主要原因和防止潮湿的主要措施？
नमी की रिपोर्ट के अनुसार नमी के मुख्य कारण और नमी को रोकने के लिए मुख्य कार्य क्या हैं?
Que dit le rapport sur l’humidité concernant les principales causes de l’humidité et les principales actions pour l’arrêter?
Was sagt der Feuchtigkeitsbericht über die Hauptursachen von Feuchtigkeit und die Hauptmaßnahmen zur Bekämpfung von Feuchtigkeit?
Что говорится в отчете о влажности о основных причинах влажности и основных действиях по ее устранению?
Cosa dice il rapporto sull’umidità riguardo le principali cause dell’umidità e le principali azioni per fermarla?